ALSTOM EPSD-0603 DFI-150-0003
Product Name: ALSTOM EPSD-0603 DFI-150-0003 — Enhanced Protection & Trip (Voting) Module for Turbine Safety System
Product Brief: Part of Alstom's EPSD (Enhanced Protection System Device) family — a dedicated hardware-based protection/trip module used in turbine overspeed, vibration, or process-limit voting logic. The DFI-150 designation typically refers to a Digital Fault Input or trip-conditioning interface board within the protection chain. Works in conjunction with EP3 / T3000 racks to implement 2oo3 or 1oo2 voting for turbine trips.
ALSTOM EP3-E-4-A
Product Name: ALSTOM EP3-E-4-A Enhanced Protection Analog I/O Module (for DEH / Turbine Control)
Product Brief: A high-reliability analog input/output module belonging to Alstom's (now GE Power) P320/P325 or Mark VIe distributed turbine control architecture. Used for acquiring analog field signals (temperature, pressure, position) or generating 4–20 mA analog outputs for valve positioning in steam/gas turbine DEH systems.
ATOS E-ME-AC-05F
Product Name: ATOS E-ME-AC-05F Analog Eurocard-type Electronic Amplifier
Product Brief: An analog-type electronic amplifier in Eurocard format (DIN 41494), designed to drive Atos proportional directional valves and pressure/flow control valves equipped with two solenoids (double electromagnetic actuator) but without position or pressure feedback sensors. It converts a reference voltage or current signal into a PWM-controlled current output to position the valve spool proportionally.
FOXBORO FBM232 P0926GW
-
Product Name: Foxboro (Schneider Electric) FBM232 P0926GW Ethernet FDSI Field Device Integration Module
-
Product Introduction: A single-port 10/100 Mbps Ethernet communication module for Foxboro I/A Series and Evo DCS. Enables integration of third-party Ethernet-enabled field devices (PLCs, intelligent instruments, VFDs, analyzers) using Modbus TCP, EtherNet/IP (via downloadable driver), or other FDSI protocol stacks. Acts as a gateway between the Foxboro Control Station and external Ethernet devices.
FOXBORO FBM214B RH101AB
-
Product Name: Foxboro (Schneider Electric) FBM214B 8-Channel Isolated Analog Input Module with HART Pass-Through
-
Product Introduction: A high-resolution analog input module for the Foxboro I/A Series Distributed Control System (DCS). Accepts 4–20 mA, 0–20 mA, 0–5 VDC, 1–5 VDC, or 0–10 VDC signals from field transmitters and provides 16-bit resolution with full channel-to-channel and channel-to-ground isolation. Supports HART digital communication pass-through to asset management software.
SEW-EURODRIVE FBG31C-08
-
Product Name: SEW-EURODRIVE FBG31C-08 Braking (Chopper) Resistor for Frequency Inverter Regenerative Braking
-
Product Introduction: External dynamic braking resistor from SEW-EURODRIVE's FBG series, intended for connection to the DC-link brake chopper terminal of SEW MOVIDRIVE® B (MDX61B) or MOVITRAC® LTE-B inverters. Dissipates regenerative energy from decelerating high-inertia or overhauling loads that would otherwise cause DC-bus overvoltage.
KEBA FB201
-
Product Name: KEBA FB201 Motion Control / Servo Drive Interface Module
-
Product Introduction: A high-performance motion control module from KEBA's FB-series, designed for precise positioning, speed, and torque control of servo axes in packaging, printing, robotics, and CNC applications. Interfaces between a higher-level PLC/controller and the servo amplifier/drive.
DEIF FAS-113DG
-
Product Name: DEIF FAS-113DG Automatic Synchronizer Module with Load-Share Interface (Gen-set Synchronizing)
-
Product Introduction: Enhanced version of the FAS-2R family, the FAS-113DG provides automatic synchronization plus analog outputs for interfacing with DEIF LSU-122DG (voltage droop/load share) and LSU-112/113/114DG (frequency load share) units for island-mode load sharing after paralleling.
DEIF FAS-2R
-
Product Name: DEIF FAS-2R Automatic Synchronizer Module (Generator-to-Busbar Synchronization)
-
Product Introduction: A compact synchronizer from DEIF's FAS series used in genset control panels to automatically match generator voltage, frequency, and phase angle with the mains/busbar before closing the breaker. Often paired with DEIF AGC/AMF or LSU load-sharing units.
HIMA F8650X
-
Product Name: HIMA F8650X Safety Controller / Central Processing Unit Module (HIMax / HIQuad X Series)
-
Product Introduction: Successor to F8650E, the F8650X is the central CPU for HIMA HIMax and HIQuad X SIS platforms. Offers enhanced processing speed, larger memory, and native support for modern fieldbuses. Designed for ESD, F&G, HIPPS, turbine protection, and other SIL 3 / SIL 4 applications.
HIMA F8650E
-
Product Name: HIMA F8650E Safety System Central Processing Unit (CPU) Module
-
Product Introduction: The core processor for HIMA HIQuad (H51q) Safety Instrumented Systems. Executes user safety application program, performs 1oo2D / 2oo4D redundant processing, manages I/O communication, and logs Sequence of Events (SOE). Certified SIL 3 for ESD, HIPPS, F&G, burner management applications.
HIMA F6217
-
Product Name: HIMA F6217 Safety Digital Input Module, 16-Channel, 24 VDC
-
Product Introduction: A safety-related discrete input module for HIMA H41q/H51q and HIMax systems, designed to acquire 16 dry-contact or 24 VDC proximity signals from field sensors (e.g., emergency pushbuttons, limit switches, valve feedback) and feed them into the safety logic solver with galvanic isolation and comprehensive diagnostics.
