GE NE724A
Product Introduction
The NE724A is a high-density, 48 VDC digital input module from GE Vernova, engineered for reliable monitoring of discrete signals in industrial automation and turbine control systems. It features 16 isolated input channels, each with optical isolation to eliminate ground loops and noise interference, ensuring accurate signal acquisition in harsh industrial environments. The module integrates seamlessly with GE’s Mark VIe turbine control systems and PACSystems RX3i/RX7i programmable automation controllers, supporting ToolboxST configuration software for quick setup and diagnostics.
GE P110-6052
Product Introduction
The P110-6052 is a high-reliability 24 VDC redundant power supply module designed by GE Vernova for industrial automation and turbine control systems. It delivers a stable 24 VDC output to support critical loads in PACSystems RX3i/RX7i programmable automation controllers and Mark VIe turbine control systems. The module features redundant architecture, enabling seamless switchover between two power inputs to eliminate single points of failure and maximize system availability. It integrates advanced protection mechanisms against overvoltage, overcurrent, short circuits, and over-temperature, ensuring the safety of connected devices and the power supply itself.
GE PCH1026
Product Overview
The GE PCH1026 is a highly configurable digital structural vibration monitor engineered for low‑frequency (0.05–1000 Hz) monitoring in wind turbines, developed in collaboration with global turbine manufacturers and protecting over 100,000 units worldwide. It integrates a 3‑axis internal accelerometer (X/Y/Z) and up to 4 external sensor inputs to capture acceleration, velocity, and displacement across critical turbine structuresPCH Engineering A/S. The unit uses advanced DSP with 50% overlap FFT, 127 zoom ranges, and programmable filters to isolate structural modes from operational noise, delivering precise RMS/Peak/Peak‑to‑Peak measurements.
GE PCH1026CHF861016
Product Introduction
The PCH1026CHF861016 is a high-precision triaxial digital structural vibration monitor engineered by GE Vernova for low-frequency vibration monitoring in wind energy and industrial applications. It integrates three internal accelerometers (X, Y, Z axes) to capture comprehensive structural motion data, supporting up to 4 independent frequency bands per sensor for detailed analysis. The module employs advanced DSP technology and field-proven filtering algorithms to measure RMS, peak, and peak-to-peak values with exceptional accuracy.
GE PMC-0247RC-282000 350-93750247-282000F Compact Intelligent PLC & I/O Module for GE PACSystems RX3i
Technical Specifications:
- Function Type: This module serves as a processor or input/output (I/O) interface component within the turbine control system, responsible for signal processing, data acquisition, and command execution.
- Processor and Memory: Equipped with a high-speed digital signal processor (DSP) and sufficient onboard memory to support real-time control algorithms, diagnostics, and firmware operations.
- Communication Interface: Supports high-speed communication via Ethernet or fiber optic links, enabling integration with the central control system and other field devices using protocols such as Profibus, Modbus, or proprietary GE control networks.
- I/O Support: Designed to interface with analog and digital signals from sensors and actuators, including temperature, pressure, speed, and valve position feedback.
GE PQMII-T20
Product Introduction
The GE PQMII - T20 is a high - precision three - phase power quality meter from GE Multilin’s PQMII series, designed for continuous monitoring, analysis and energy management of electrical power systems. It precisely measures a full set of electrical parameters, performs in - depth harmonic analysis up to the 63rd harmonic, and captures transient events like voltage sags, swells, and flicker with high - speed sampling. It is equipped with 4 isolated 4 - 20mA analog outputs, 4 programmable relay outputs, 4 digital inputs, and multiple communication interfaces, enabling seamless integration with SCADA, PLC, and energy management systems.
GE PQMII-T20
Technical Specifications:
- Measurement Standards: IEC 61000-4-30 Class A compliant for power quality monitoring
- Voltage Inputs: 3-phase or single-phase configurations, typical ranges up to 690 V AC
- Current Inputs: Compatible with Rogowski coils, CTs (current transformers), or clamp sensors
- Sampling Rate: High-speed sampling for transient and waveform capture
- Frequency Range: 45 Hz to 65 Hz (extendable for special applications)
- Voltage Accuracy: ±0.1% of reading
- Current Accuracy: ±0.5% of reading
- Harmonic Analysis: Up to 63rd harmonic for voltage and current
GE PQMII-T20-C
Product Overview
The GE PQMII-T20-C is a high-precision power quality meter from the PQM II Series, engineered for continuous monitoring, analysis, and control of three-phase electrical systems in industrial, commercial, and utility applications. It delivers comprehensive measurement of voltage, current, power, energy, frequency, harmonics, and power quality events (sags, swells, transients) with industry-leading accuracy. The unit supports 20 current inputs and 4 voltage inputs for multi-circuit monitoring, integrates 4 isolated analog outputs, 4 relay outputs, and 4 switch inputs for control/alarming, and offers Modbus RTU communication via RS232/RS485. It includes advanced features such as 63rd harmonic analysis, voltage disturbance recording (VDR), event logging, and waveform capture to diagnose power quality issues and protect critical assets.
GE PQMII-T20-C-A
Product Introduction
The GE PQMII-T20-C-A is a high-precision three-phase power quality meter from GE Multilin’s PQMII series, tailored for industrial and utility applications requiring advanced power monitoring, harmonic analysis, and energy management. It delivers comprehensive measurement of electrical parameters, in-depth harmonic analysis up to the 63rd harmonic, and high-speed capture of voltage sags, swells, flicker, and transient events. It is equipped with 1 isolated 4-20mA analog input, 4 isolated 4-20mA analog outputs, 4 digital inputs, and 4 programmable relay outputs, alongside multiple communication interfaces for seamless integration with SCADA, PLC, and energy management systems.
GE PWB68A993125
Product Overview
The GE PWB68A993125 is a dedicated industrial control printed circuit board designed for SCR (Silicon Controlled Rectifier) gate driving, signal filtering, and electrical interface management in industrial automation, HVAC, and power control systems. It integrates SCR gate drive circuits, signal filtering stages, and terminal blocks to enable precise switching and regulation of SCR-based power circuits, ensuring stable load control and protection against electrical noise/interference. The board supports direct connection to standard industrial sensors, controllers, and SCR power modules, and operates reliably in harsh industrial environments with wide temperature ranges and electrical noise immunity. It serves as a critical interface between control systems (PLCs, DCS) and power switching components, facilitating seamless integration and enhanced system safety.
GE RANGE-80 TO 20°C
Product Introduction
The GE HygroPro series dew point transmitter with measurement range -80°C to 20°C is a high-precision moisture monitoring device engineered for industrial applications requiring accurate and reliable dew/frost point measurement in gases. It utilizes advanced sensor technology to deliver stable readings across the -80°C to 20°C range, with rapid response to moisture changes and robust performance in harsh environments. The transmitter features a Type 4X/IP67-rated enclosure for protection against dust and water ingress, ensuring durability in outdoor, offshore, and industrial settings.
