ProSoft PTQ-PDPMV1 - Image 1
ProSoft PTQ-PDPMV1 - Image 2
Click to enlarge
ProSoft PTQ-PDPMV1
ProSoft PTQ-PDPMV1 - Image 2
Microelettrica Scientifica PTC1177
Microelettrica Scientifica PTC1177
Back to products
NI PXIe-8135
NI PXIe-8135

ProSoft PTQ-PDPMV1

Product Brief:​ Single-slot Quantum backplane module that turns a Schneider Quantum PLC into a PROFIBUS DP-V1 Class 1 Master. Enables cyclic I/O exchange and acyclic services (alarms, parameterization, diagnostics) with up to 125 PROFIBUS slave devices.

Category:
Description
Key Technical Specifications:
  • Platform Compatibility:​ Schneider Electric Quantum series (140CPUxxxx) with Unity Pro / Concept
  • Protocol:​ PROFIBUS DP-V0 + DP-V1 (Master, Class 1 & Class 2 services)
  • Communication Port:​ 1 × 9-pin D-sub female (RS-485), optically isolated
  • Baud Rate:​ 9.6 kbps to 12 Mbps (auto-baud detection supported)
  • Max Slaves:​ 125 (31 per segment without repeater; add repeaters for more)
  • Cyclic Data Capacity:​ Up to 1536 bytes Input + 1536 bytes Output (per master — depends on PLC memory mapping)
  • Backplane Current Draw:​ max 1100 mA @ 5 VDC
  • Configuration:​ ProSoft Configuration Builder (PCB) software; also FDT/DTM via ComDTM for offline/on-line configuration
  • Hot Standby Support:​ Compatible with Quantum Hot Standby (HEC) — max 4 PTQ modules per rack in HS config
  • Processor:​ Infineon C165 microcontroller + Siemens ASPC2 Step E ASIC
  • Status Indicators:​ Module STAT, Backplane COM, Master RUN, Net Diag, Token LEDs
  • Mechanical:​ Standard Quantum single-width module (approx. 250 × 103.9 × 40.3 mm)
  • Operating Temp:​ 0°C to +60°C
  • Humidity:​ 5–95% RH non-condensing
  • Vibration/Shock:​ IEC 60068-2-6(3 g, 10–150 Hz), IEC 60068-2-27(30 g, 11 ms)
  • Certifications:​ CE, UL, CSA, PROFIBUS PTO certified, ATEX Zone 2 (some revisions)
Features:​ Extended DP-V1 diagnostics (read slave diagnostic alarms), online slave parameter write/read, supports multiple masters in one Quantum rack, built-in web server on some firmware versions for basic diagnostics.
Applications:​ Integrating legacy or third-party PROFIBUS DP field devices (drives, valves, remote I/O, analyzers) into Schneider Electric Quantum process control or SCADA systems; retrofit of S5-interface machinery into modern DCS/PLC architecture.
Installation & Notes:​ Install in any available slot except slot 1 (reserved for CPU in most Quantum racks). Terminate PROFIBUS network both ends with 220 Ω resistors. Use screened twisted pair (PROFIBUS cable type A). Ensure GSD file from ProSoft is imported into configuration tool. Set correct station address via DIP switches or software before inserting into live rack.
Reviews (0)

Reviews

There are no reviews yet.

Be the first to review “ProSoft PTQ-PDPMV1”

Your email address will not be published. Required fields are marked *

Shipping and Delivery
wd-ship-1
wd-ship-2

MAECENAS IACULIS

Vestibulum curae torquent diam diam commodo parturient penatibus nunc dui adipiscing convallis bulum parturient suspendisse parturient a.Parturient in parturient scelerisque nibh lectus quam a natoque adipiscing a vestibulum hendrerit et pharetra fames nunc natoque dui.

ADIPISCING CONVALLIS BULUM

  • Vestibulum penatibus nunc dui adipiscing convallis bulum parturient suspendisse.
  • Abitur parturient praesent lectus quam a natoque adipiscing a vestibulum hendre.
  • Diam parturient dictumst parturient scelerisque nibh lectus.

Scelerisque adipiscing bibendum sem vestibulum et in a a a purus lectus faucibus lobortis tincidunt purus lectus nisl class eros.Condimentum a et ullamcorper dictumst mus et tristique elementum nam inceptos hac parturient scelerisque vestibulum amet elit ut volutpat.

Related products

ProSoft AN-X2-AB-DHRIO EtherNet

  • Technical Specifications
    • Power Supply Parameters
      • The typical power consumption is 200mA at 12V DC or 100mA at 24V DC, with a maximum power consumption of 2.4W. It adapts to the common low - voltage DC power supply environment in industrial sites and has low overall energy consumption.
    • Communication Parameters
      • It is equipped with one RJ45 10/100 Mbps Ethernet port and one DH+/Remote I/O port. It supports DH+, Remote I/O and EtherNet/IP protocols and now supports DH+ migrations on SLC networks.
      • It supports all DH+ and Remote I/O baud rates, which are 57.6k baud, 115.2k baud and 230.4k baud, and Remote I/O addressing ranges from 0 to 76 octal.
    • Environmental and Physical Parameters
      • The operating temperature ranges from 0°C to 50°C, and the storage temperature ranges from -40°C to 85°C. It can withstand extreme temperature changes in both indoor and outdoor industrial environments.
      • The relative humidity tolerance is 5% to 95% non - condensing. Its dimensions are 107mm x 126mm x 34mm excluding connectors, and it weighs approximately 310 grams. It supports DIN rail mounting for convenient integration into industrial control cabinets.
Read more
Quick view

ProSoft MVI56-MDA4 MDA Scientific CM4 Gas Analyzer Master Module

Technical Specifications
  • Mechanical and Backplane Specifications
    • It is compatible with the 1756 backplane, adopts a single - slot design, and can be installed in both local and remote racks of ControlLogix chassis. It is recognized as a standard input and output module by the ControlLogix system and can access the processor memory smoothly.
  • Electrical Parameters
    • The input voltage ranges from 110V AC to 240V AC, and the operating frequency is 50Hz or 60Hz. The maximum power consumption does not exceed 5W, which shows low energy consumption and has little impact on the overall power load of the industrial control system.
  • Communication and Measurement Parameters
    • It supports Modbus RTU and Modbus ASCII communication protocols, is equipped with two RS - 232 communication ports for connecting to CM4 gas analyzers, and an RJ45 serial port for configuration operations.
    • The sampling rate can reach up to 10Hz. For common gases, the measurement range includes 0 - 25% volume for oxygen and 0 - 20000 ppm for carbon monoxide, with a measurement accuracy of ±0.5%.
Read more
Quick view

ProSoft MVI56-MNETR Modbus TCP

  • Technical Specifications
    • Mechanical and Power Parameters
      • It adopts a single-slot design compatible with the Controllogix 1756 backplane, enabling easy installation into Controllogix chassis without occupying excessive space.
      • The backplane current load reaches 800 mA under 5 VDC and 3 mA under 24 VDC, matching the power supply requirements of Controllogix systems for stable operation.
    • Communication Parameters
      • It is equipped with a 10/100 Mbps Ethernet interface with auto-crossover detection, using an RJ45 connector suitable for Cat5 cables, and it supports Ethernet/IP pass-through communication.
      • It supports storage and transfer of up to 5000 16-bit registers with the Controllogix processor through block transfer or side-connect interface. Client parameters are configurable, including a minimum response delay ranging from 0 to 65535 milliseconds, and it also supports floating-point data types.
    • Environmental and Display Parameters
      • The operating temperature ranges from 0 °C to 60 °C, and the storage temperature ranges from -40 °C to 85 °C. It can operate normally in 5% to 95% relative humidity environments without condensation.
      • It is equipped with a 4-character scrolling alphanumeric LED display that shows module version, IP address, application port settings and error information, along with LED indicators for module status, application status and error status.
Read more
Quick view

ProSoft MVI56-PDPMV1 PROFIBUS DP-V1 Master Network Interface Module for ControlLogix

  • Technical Specifications
    • Power and Physical Parameters
      • It is compatible with the 1756 backplane and occupies a single slot. The backplane current load is 800 mA at 5.1 VDC and 3 mA at 24 VDC, matching standard ControlLogix chassis power supply configurations.
      • The operating temperature range is 0°C to 60°C, and the storage temperature range is -40°C to 85°C. It can operate normally in an environment with 5% to 95% relative humidity without condensation.
      • It resists 30g operational shock and 50g non-operational shock, and can withstand 5g vibration within the frequency range of 10Hz to 150Hz, adapting to harsh industrial site conditions.
    • Communication Parameters
      • It supports all standardized PROFIBUS baud rates, with the maximum baud rate reaching 12 Mbps, meeting the requirements of high-speed data transmission in industrial scenarios.
      • It can connect up to 125 slave devices and can access PROFIBUS PA slaves through DP/PA couplers or links. It also allows multiple master modules to be installed in a single rack to expand network capacity.
      • It is equipped with an RS-232 configuration port with an RJ45 interface, and comes with an RJ45 to DB-9 male cable for on-site configuration and debugging.
    • Software Compatibility Parameters
      • It works with ProSoft Configuration Builder software, supporting functions such as importing project-specific GSD files and automatic bus parameter calculation.
      • It uses ladder logic for data transfer between the module and the processor, and a sample ladder file with add-on instructions is provided to simplify the configuration process for users.
      • It supports communication with configuration software via Ethernet routing through Rockwell Automation Ethernet interfaces such as 1756-ENBT and 1756-EN2T.
Read more
Quick view

ProSoft MVI69-PDPMV1

Product Overview The MVI69-PDPMV1 is a PROFIBUS DP-V1 master module designed by ProSoft Technology for Rockwell Automation's CompactLogix and MicroLogix PLCs. It serves as a bridge connecting PLCs to PROFIBUS network slave devices, enabling data exchange and control. This module is widely used in industrial automation systems to integrate devices from different manufacturers. Technical Specifications
  • Interface: PROFIBUS DP-V1
Read more
Quick view

ProSoft PLX32-EIP-SIE Industrial Ethernet Communication Gateway

Technical Specifications
  • Power and Physical Parameters
    • It operates on a 24 VDC power supply and has a power consumption of approximately 5W, which is compatible with standard industrial power supply systems.
    • Its dimensions are 118 mm x 85 mm x 75 mm, and it adopts a compact structural design that saves installation space. It can be flexibly installed in various industrial control cabinets.
    • It has an operating temperature range of -40°C to 85°C, which allows it to run stably in extreme temperature environments such as cold workshops and high-temperature processing areas. It also features strong environmental adaptability with protection against dust and moisture.
  • Communication Parameters
    • It is equipped with Ethernet RJ-45 interfaces, supporting 10/100 Mbps Ethernet transmission rates to meet the data transmission needs of most industrial scenarios.
    • It supports dual subnet capability, allowing each protocol to reside on separate Ethernet subnets, which enhances the flexibility of network configuration.
    • It is compatible with multiple protocols including EtherNet/IP, Siemens Industrial Ethernet and Modbus TCP/IP, and realizes smooth protocol conversion and data interaction between different networks.
Read more
Quick view

ProSoft PLX32-MBTCP-SIE

Product Name:​ ProSoft Technology PLX32-MBTCP-SIE Modbus TCP/IP to Siemens S7 Industrial Ethernet Communication Gateway
Product Introduction:​
An industrial protocol gateway that enables bidirectional data exchange between Modbus TCP devices (Client and/or Server) and Siemens S7 PLCs (S7-300/400/1200/1500) over Siemens Industrial Ethernet. Eliminates need for custom drivers in mixed-vendor automation networks.
Read more
Quick view

ProSoft PTQ-PDPMV1 PROFIBUS DPV1 Master Network Interface Module for Quantum Processors

Technical Specifications
  • Power and Physical Parameters
    • It uses a 24VDC power supply and has a power consumption of 1.5W, which is compatible with standard industrial power supply configurations.
    • Its dimensions are 110 mm × 95 mm × 50 mm and weighs 0.5 kg. The compact size allows for flexible installation in industrial control cabinets.
    • It operates within a temperature range of -40°C to 85°C and can withstand a humidity range of 5% to 95% without condensation, adapting to harsh industrial environmental conditions.
  • Communication Parameters
    • It serves as a PROFIBUS DPV1 master interface and supports baud rates ranging from 9600 bps to 12 Mbps, with automatic baud rate detection for all valid PROFIBUS DPV1 rates.
    • It can connect up to 125 slave devices when using repeaters, and can also connect PROFIBUS PA slaves to the network through DP/PA couplers or links.
    • It requires Ethernet connectivity for normal operation, and uses UDP messaging to back up data in status registers between modules to determine switchover conditions.
Read more
Quick view