Bently Nevada 3500/22M 138607-01 Transient Data Interface (TDI) Module - Image 1

Bently Nevada 3500/22M 138607-01 Transient Data Interface (TDI) Module - Image 2

Bently Nevada 3500/22M 138607-01 Transient Data Interface (TDI) Module

Technical Specifications
– Host position : slot 1 (full-height), mandatory in every 3500 rack
– Input channels : 22 dynamic + 24 static/process channels
– Sampling rate : 102.4 kHz per dynamic channel, synchronous across the rack
– Resolution : 16-bit ADC, <0.02 % non-linearity, 30 ppm/°C drift
– Frequency range : 0.3 Hz – 40 kHz (–3 dB) with programmable high-pass, low-pass and notch filters
– On-board memory : 2 GB for transient buffer, event log and firmware
– Communication ports :
– 10/100BASE-TX auto-negotiating copper Ethernet (RJ-45)
– 100BASE-FX fiber-optic Ethernet (optional)
– USB-B front service port (38.4 kbaud)
– RS-232 / RS-485 (38.4 kbaud, Modbus RTU)
– Protocols : Modbus TCP/RTU, proprietary Bently protocol, OPC UA tunnel
– Power draw : 24 Vdc from rack back-plane, 10.5 W typical, <15 W max
– Isolation : 1 500 Vac channel-to-ground, 500 V channel-to-channel
– MTBF : >250 000 h @ 45 °C per MIL-HDBK-217F
– Operating temperature : –40 °C to +70 °C full performance
– Storage temperature : –40 °C to +85 °C
– Humidity : 5 %–95 % non-condensing
– Shock / vibration : 15 g half-sine 11 ms; 5 g 5–500 Hz operational
– Dimensions : 229 mm × 140 mm × 48 mm (9.0″ × 5.5″ × 1.9″)
– Weight : 1.0 kg (2.2 lb)
– Agency approvals : CE, UL/cUL Class I Div 2, ATEX/IECEx Zone 2, RoHS, ABS marine

Category: Bentley

Description

Functional Highlights
– Slot-1 mandatory – every 3500 rack requires one TDI; auto-discovers and addresses all monitor modules
– Dual redundancy – two TDIs can be fitted in TMR racks; automatic switch-over <5 ms without data loss
– Hot-swappable – insertion/extraction under full rack power without interrupting protection or process monitoring
– Transient capture – programmable pre- and post-trigger buffers (up to 16 000 samples) catch fast events such as blade loss, surge or gear-tooth breakage
– Multi-channel sync – supports simultaneous sampling on 22 dynamic channels, ensuring phase-coherent data for orbit and balancing analysis
– Time sync – accepts IRIG-B, PTP or SNTP to timestamp events to ±1 ms across entire plant network
– Event historian – stores >50 000 system events, alarm logs and operator actions with 1 ms resolution
– Firmware flash – field-upgradeable via Ethernet in <3 min; rollback image stored for safety
– TMR ready – special firmware performs 2-out-of-3 channel voting when used in triple-modular-redundant racks
– Cyber-secure – role-based access, SSL/TLS encryption, syslog forwarding to SIEM platforms

Application Scenarios
– Steam & gas turbine TSI cabinets – interfaces rack data to GE Mark VIe, Siemens SPPA-T3000 or Emerson Ovation DCS
– Offshore platform centrifugal compressors – redundant fiber-Ethernet rings send vibration data to onshore System 1 servers
– LNG refrigeration trains – 102.4 kHz sampling captures gear-mesh harmonics for early tooth-fault detection
– Ethylene hyper-compressors – transient buffers store start-up and surge events for root-cause analysis
– Cross-country pipeline pump stations – IRIG-B time sync aligns multiple racks along 500 km right-of-way
– Steel mill blast-furnace blowers – Zone-2 certification allows direct mounting in hazardous junction boxes
– Wind-turbine test stands – high-speed Modbus TCP feeds real-time data to LabVIEW or MATLAB for modal analysis
– Nuclear feed-water pumps – TMR configuration meets IEEE 338 requirements for safety-related monitoring

Installation & Maintenance
Slides into slot 1 of any 3500 rack; captive screws provide chassis earth bond. Front LEDs indicate module healthy, network link, serial traffic and transient-capture status. RJ-45 and DB-9 front connectors accept standard Cat-5e and RS-232 cables; no separate power wiring is required. Onboard diagnostics report fan life, supply margin and internal temperature over the same Ethernet link, enabling fully remote health dashboards. Module replacement takes <1 min; all rack parameters remain stored non-volatilely on every monitor, so no re-configuration is necessary

Compatibility
Backward- and forward-compatible with every 3500 monitor produced since 1998 (3500/40M, 3500/42M, 3500/44M, 3500/45, 3500/46M, 3500/50, 3500/60, 3500/62, 3500/70M, 3500/72M, 3500/77M, 3500/90, 3500/92, 3500/93). Operates seamlessly with legacy TDIX/DDIX and current TDI communication processors. Supported by System 1 v6.5 onward and by third-party OPC UA, Modbus and DNP3 clients

Ordering Reference
3500/22-01-01-00 138607-01 – Standard TDI, copper Ethernet, RS-232, conformal coat
3500/22-01-02-00 138607-01 – As above plus 100BASE-FX fiber port
3500/22-02-01-00 138607-01 – TMR version for triple-redundant racks
3500/22-AXX-BXX-CXX – Full modular option table for cable length, firmware revision and hazardous-area certification

Reviews (0)

Reviews

There are no reviews yet.

Be the first to review “Bently Nevada 3500/22M 138607-01 Transient Data Interface (TDI) Module”

Shipping and Delivery

MAECENAS IACULIS

Vestibulum curae torquent diam diam commodo parturient penatibus nunc dui adipiscing convallis bulum parturient suspendisse parturient a.Parturient in parturient scelerisque nibh lectus quam a natoque adipiscing a vestibulum hendrerit et pharetra fames nunc natoque dui.

ADIPISCING CONVALLIS BULUM

Vestibulum penatibus nunc dui adipiscing convallis bulum parturient suspendisse.
Abitur parturient praesent lectus quam a natoque adipiscing a vestibulum hendre.
Diam parturient dictumst parturient scelerisque nibh lectus.

Scelerisque adipiscing bibendum sem vestibulum et in a a a purus lectus faucibus lobortis tincidunt purus lectus nisl class eros.Condimentum a et ullamcorper dictumst mus et tristique elementum nam inceptos hac parturient scelerisque vestibulum amet elit ut volutpat.