Bürkert SE35 00423924 - Image 1
Bürkert SE35 00423924 - Image 2
Bürkert SE35 00423924 - Image 3
Click to enlarge
Bürkert SE35 00423924
Bürkert SE35 00423924 - Image 2
Bürkert SE35 00423924 - Image 3
Yokogawa SCP451-51
Yokogawa SCP451-51
Back to products
Emerson SE4001S2T2B1
Emerson SE4001S2T2B1

Bürkert SE35 00423924

Product Introduction:​
The SE35 is a snap-on electronic display/transmitter module that mounts onto a Bürkert S030 paddle-wheel sensor housing to form the Type 8035 flowmeter or batch controller. It converts the frequency signal from the turbine sensor into a scalable analog (4–20 mA) and/or pulse output, and displays instantaneous flow rate and totalized volume on a local LCD.
Category:
Description
Key Features:
  • Large backlit LCD showing flow rate + two totalizers (resettable daily / non-resettable grand)
  • Teach-in calibration via keypad (K-factor entry)
  • NPN/PNP pulse output and 4–20 mA analog output
  • Optional relay outputs for batch control or alarm (depending on exact SE35 variant; 00423924 typically includes display + 4–20 mA + pulse)
  • Compatible with S030 sensors in DN06–DN65
Technical Specifications (SE35 + S030 system):
  • Supply Voltage:​ 12–36 VDC (loop-powered 4–20 mA option available on some variants; 00423924 typically 24 VDC)
  • Analog Output:​ 4–20 mA, proportional to flow (2-wire loop or 3-wire isolated — variant dependent)
  • Pulse Output:​ NPN or PNP open-collector, scalable
  • Accuracy:​ ≤ ±(0.5 % FS + 2.5 % reading)
  • Repeatability:​ ≤ ±0.4 % of reading
  • Flow Range (system):​ 0.3–10 m/s (depends on pipe size / S030 orifice)
  • Media Temperature:​ 0 to +100 °C (with suitable S030 body)
  • Ambient Temp.:​ 0 to +60 °C
  • Electrical Connection:​ DIN EN 175301-803(Form A / PG9) cable plug
  • Protection Rating:​ IP65 when plug properly connected
  • Display:​ 6-digit LCD with flow unit, totalizer digits
  • Material (module):​ Polyamide / PC housing; S030 wetted parts SS316L / PVDF / PP / PVC / brass per selection
Applications:​ Water treatment dosing, chemical batching, CIP (Clean-in-Place) flow verification, beverage & food liquid monitoring, cooling-water flow supervision.
Installation Notes:​ Match K-factor of the S030 paddle-wheel sensor exactly during programming. Use shielded cable for 4–20 mA run; ground shield at one end only (supply side). Do not expose electronic module to direct wash-down beyond IP65 rating unless protective cover is fitted.
Reviews (0)

Reviews

There are no reviews yet.

Be the first to review “Bürkert SE35 00423924”

Your email address will not be published. Required fields are marked *

Shipping and Delivery
wd-ship-1
wd-ship-2

MAECENAS IACULIS

Vestibulum curae torquent diam diam commodo parturient penatibus nunc dui adipiscing convallis bulum parturient suspendisse parturient a.Parturient in parturient scelerisque nibh lectus quam a natoque adipiscing a vestibulum hendrerit et pharetra fames nunc natoque dui.

ADIPISCING CONVALLIS BULUM

  • Vestibulum penatibus nunc dui adipiscing convallis bulum parturient suspendisse.
  • Abitur parturient praesent lectus quam a natoque adipiscing a vestibulum hendre.
  • Diam parturient dictumst parturient scelerisque nibh lectus.

Scelerisque adipiscing bibendum sem vestibulum et in a a a purus lectus faucibus lobortis tincidunt purus lectus nisl class eros.Condimentum a et ullamcorper dictumst mus et tristique elementum nam inceptos hac parturient scelerisque vestibulum amet elit ut volutpat.

Related products

CCC TIOC-555HD

Technical Specifications

There is currently no specific and detailed technical specification information available for the CCC TIOC - 555HD. However, based on similar products such as the CCC IOC - 555 - D, it may have the following characteristics:
  • Communication Interface: May support RS - 485 communication.
  • I/O Channels: It is possible to have multiple digital inputs and outputs, as well as analog inputs and outputs. For example, the IOC - 555 - D has 8 digital inputs, 4 digital outputs, 2 analog inputs, and 2 analog outputs.
Read more
Quick view

Elmo G-TUB30480ERSS0

  • Rated Voltage: 480 VAC
  • Rated Current: 30 A
  • Continuous Power: Up to 25 kW
  • Communication Interfaces: Ethernet, CANopen, RS232, EtherCAT, etc.
  • Feedback Types: Encoder, resolver, Hall sensor (depending on the model)
  • Operating Temperature Range: - 40°C to +70°C (industrial - grade)
  • Protection Level: IP20 or higher (depending on the model)
  • Installation Method: Rack - mount, DIN - rail mount (depending on the model)
Read more
Quick view

KEBA FB201 — Comprehensive Data Sheet

Procurement Guidance

  1. Compatibility Notes
    • Verify suffix codes (e.g., FB201/xxx) for I/O capacity and environmental ratings .
    • Requires KEBA RobotStudio or ECL-3 software for configuration .
  2. Critical Accessories
    • Backplane Adapter (e.g., SDCS-PIN-24) for PLC integration .
    • IP65 Housing for harsh environments (e.g., oil rigs, substations) .
  3. Avoid Mismatches
    • Servo drives → Refer to KEBA KeDrive.
    • HMIs → Use KEBA ETT Series.
Read more
Quick view

KONGSBERG MRU-E-JB3

Technical Specifications:
  • Measurement Axes: 6 DOF (Degrees of Freedom) - heave, surge, sway, roll, pitch, and yaw
  • Accuracy: High accuracy across all axes with minimal latency
  • Update Rate: Configurable up to 100 Hz for real-time applications
  • Operating Voltage: Typically 12 to 36 VDC
  • Power Consumption: Low power consumption suitable for extended operation
  • Operating Temperature: -40°C to +70°C, ensuring performance in extreme environments
  • Storage Temperature: -50°C to +85°C
  • Humidity Range: 0% to 100% relative humidity, waterproof design
  • Environmental Protection: IP68 rated for underwater use and protection against dust and water ingress
  • Communication Interfaces: RS-232, RS-422, Ethernet, NMEA 0183, and others depending on configuration
Read more
Quick view

SAACKE FSC-01

Technical Specifications:
  • Supply Voltage: 24 V DC (typical), with options for 110–230 V AC in certain configurations
  • Power Consumption: Low power draw, optimized for continuous operation
  • Operating Temperature: -10°C to +55°C
  • Storage Temperature: -25°C to +70°C
  • Humidity Range: 5% to 95% relative humidity, non-condensing
  • Protection Rating: IP20 (suitable for indoor panel mounting)
  • Input Compatibility: Accepts signals from flame detectors including UV, IR, and ionization sensors
  • Output Relays: Equipped with safety-rated relay outputs for burner activation, alarm signaling, and system shutdown
Read more
Quick view

TOSHIBA GBU648E-S

  • Slot Capacity: Supports up to 8 modules, allowing flexible configuration with TOSHIBA’s EX10 series components (e.g., power supplies, CPUs, I/O units).
  • Power Supply Compatibility: Works with modules like PS261 (power supply) and PU11A (CPU), ensuring stable energy distribution and control logic execution.
  • Communication Modules: Integrates with Profibus DP modules (e.g., GPF611-S) for seamless connectivity with field devices, enabling real-time data exchange in industrial networks.
  • Analog/Digital Modules: Compatible with GAD668-S (analog input) and GDA664-S (analog output) modules, supporting high-precision signal processing for sensors and actuators.
  • Physical Design: Compact, rack-mounted structure optimized for space efficiency in control panels.
Read more
Quick view

XP POWER F8B6D4A3G3

Technical Specifications

  • Output Characteristics: It is a quad - output power supply, but specific output voltage and current values are not clearly provided in the existing information.
  • Dimensions: Approximately 15 × 11 × 7 inches (LxWxH).
  • Weight: About 8 lbs.
Read more
Quick view

ZYGO ZMI-2002 8020-0211-1-J Precision Measurement System

Technical Specifications:
  • The ZMI-2002 operates based on innovative interferometry principles, offering nanometer-level precision for surface form measurements.
  • It supports a wide range of optical configurations to accommodate diverse measurement needs.
  • Capable of providing high-resolution data, which ensures accurate characterization of surfaces and components.
Read more
Quick view