GE IC695ETM001 - Image 1
GE IC695ETM001 - Image 2
GE IC695ETM001 - Image 3
GE IC695ETM001 - Image 4
Click to enlarge
GE IC695ETM001
GE IC695ETM001 - Image 2
GE IC695ETM001 - Image 3
GE IC695ETM001 - Image 4
GE IC695CRU320-EN
GE IC695CRU320-EN
Back to products
GE IC695ETM001CA-ER
GE IC695ETM001CA-ER

GE IC695ETM001

  • Product Introduction: The IC695ETM001 is a single – slot, dual – port Ethernet interface module for GE PACSystems RX3i controllers, connecting the controller to 10/100 Mbps Ethernet networks, supporting TCP/IP, SRTP, Modbus TCP, and EGD protocols, and featuring an embedded switch with auto – negotiation, crossover detection, and a Station Manager port for online configuration and monitoring.
  • Manufacturer: GE Fanuc (General Electric Fanuc Intelligent Platforms, now part of Emerson Automation)
  • Module Type: Single – slot Ethernet interface module for RX3i backplane
Category:
Description
  • Processor: 200 MHz Ethernet processor
  • Ethernet Ports: 2×shielded RJ – 45 10BaseT/100BaseTX ports; one MAC address and one IP address for network interface
  • Transmission Rate: 10/100 Mbps, auto – negotiation, auto – sensing speed and crossover detection
  • Embedded Switch: Internal switch for port connection; supports auto – negotiate, speed sense, and crossover detection
  • Supported Protocols: TCP/IP, UDP, SRTP (Service Request Transport Protocol), Modbus TCP (server/client), EGD (Ethernet Global Data); SNTP for time synchronization
  • Station Manager Port: 9 – pin female D – connector (RS – 232) for local configuration and monitoring
  • Power Requirements: +5.0 VDC from backplane, nominal current 0.4 A; typical power consumption 2.0 W
  • Operating Temperature: 0°C to 60°C
  • Storage Temperature: – 40°C to 85°C
  • Relative Humidity: 5% to 95% (non – condensing)
  • Dimensions: 34 mm×140 mm×141 mm (1.34 in×5.51 in×5.55 in)
  • Weight: 0.35 kg (0.77 lbs)
  • Firmware Upgrade: Field – upgradable via WinLoader utility from RX3i CPU
  • Station Manager: Built – in Station Manager for online access and configuration
  • EGD Functionality: Supports periodic data exchange; EGD commands for reading/writing controller and EGD exchange memory
  • Modbus TCP Support: Acts as Modbus TCP server and client for flexible device communication
  • SRTP Support: Provides TCP/IP services via SRTP channels for programming and data transfer
  • Redundancy Compatibility: Works with RX3i redundancy systems (IC695RMX128) for network redundancy
  • LED Indicators: Front – panel LEDs for power, network link, activity, and module status
  • Restart Button: Recessed Ethernet Restart pushbutton for manual module restart
  • Certifications: CE, UL 61010 – 1, CSA C22.2 No. 61010 – 1; EU RoHS compliant
  • Industrial Automation Networking: Connects RX3i controllers to SCADA, HMI, and MES systems for data collection and remote monitoring
  • Process Control Integration: Enables Modbus TCP communication with field devices and EGD for real – time data exchange in oil, gas, chemical industries
  • Manufacturing Systems: Facilitates machine – to – machine communication between RX3i, Series 90 – 30, and VersaMax controllers
  • Redundant Network Design: Used in mission – critical systems with dual – port redundancy for uninterrupted network connectivity
  • Programming and Maintenance: Supports remote programming, firmware upgrades, and online diagnostics via Ethernet
Reviews (0)

Reviews

There are no reviews yet.

Be the first to review “GE IC695ETM001”

Your email address will not be published. Required fields are marked *

Shipping and Delivery
wd-ship-1
wd-ship-2

MAECENAS IACULIS

Vestibulum curae torquent diam diam commodo parturient penatibus nunc dui adipiscing convallis bulum parturient suspendisse parturient a.Parturient in parturient scelerisque nibh lectus quam a natoque adipiscing a vestibulum hendrerit et pharetra fames nunc natoque dui.

ADIPISCING CONVALLIS BULUM

  • Vestibulum penatibus nunc dui adipiscing convallis bulum parturient suspendisse.
  • Abitur parturient praesent lectus quam a natoque adipiscing a vestibulum hendre.
  • Diam parturient dictumst parturient scelerisque nibh lectus.

Scelerisque adipiscing bibendum sem vestibulum et in a a a purus lectus faucibus lobortis tincidunt purus lectus nisl class eros.Condimentum a et ullamcorper dictumst mus et tristique elementum nam inceptos hac parturient scelerisque vestibulum amet elit ut volutpat.

Related products

GE 239-RTD-AN Motor Protection Relay with RTD Inputs

unctional Features

  1. Advanced Protection Algorithms
    • 15 Thermal Curves: Configurable overload curves to match motor characteristics .
    • RTD Monitoring: Direct integration with PT100/PT1000 sensors for real-time winding temperature tracking (±0.5% accuracy) .
  2. Operational Flexibility
    • Programmable Outputs: Customizable relay actions for alarms, trips, or process signals (e.g., motor load percentage) .
    • Test Mode: Simulates faults without activating outputs for system validation .
Read more
Quick view

GE 516TX 336A4940DNP516TX — Industrial Ethernet Switch (N-Tron 516TX Series)

The GE 516TX 336A4940DNP516TX (also referred to as the N-TRON 516TX-A Industrial Ethernet Switch) is a high-reliability networking device designed for mission-critical industrial environments. Part of GE's N-TRON series, this switch delivers robust connectivity and advanced management features for industrial automation systems.
Read more
Quick view

GE ACC-5595-208 Reflective Memory Hub – Comprehensive Datasheet

The GE ACC-5595-208 (also referred to as the VMIACC-5595 Reflective Memory Hub) is a high-performance networking device designed for mission-critical industrial environments requiring deterministic data synchronization. Part of GE’s reflective memory product line, this hub delivers robust connectivity and advanced management features for real-time control systems.
Read more
Quick view

GE DS200TCQCG1AJD Mark V Series RST Overflow / Analog I/O Expansion Board

Functional Features

  1. Advanced Control & Protection
    • Real-time processing of turbine parameters (speed, temperature, pressure) with ±0.25% accuracy .
    • Fault Mitigation: Auto-triggered shutdowns for overvoltage, overload, or mechanical stress .
  2. Diagnostics & Health Monitoring
    • Embedded diagnostics for predictive maintenance (e.g., bearing vibration analysis) .
    • Event logging with timestamped fault histories for root-cause analysis .
Read more
Quick view

GE IC695CPE310 PACSystems RX3i Controller — Full Technical Profile

Technical Specifications:
  • Processor: Equipped with a powerful processor capable of handling sophisticated control algorithms and large amounts of data at high speeds.
  • Memory: Features ample user memory for program storage and execution, alongside additional memory for data logging and historical information.
  • Communication Interfaces: Supports multiple communication protocols including Ethernet/IP, Modbus TCP, and serial communications, allowing seamless integration into diverse network environments.
  • I/O Capabilities: Designed to interface with various input/output modules, supporting both discrete and analog signals for comprehensive control over field devices.
  • Redundancy Options: Offers redundancy features to enhance system reliability, ensuring continuous operation in critical applications.
  • Environmental Tolerance: Built to operate reliably under harsh industrial conditions, withstanding wide temperature ranges, vibration, and electrical noise.
Read more
Quick view

GE IC698CPE010 – Control Processor Module

The GE IC698CPE010 (also referred to as the PACSystems RX7i VME CPU) is a high-performance industrial controller designed for real-time automation and process control in mission-critical environments. As part of GE’s PACSystems RX7i platform, it combines robust hardware with flexible programming capabilities to meet the demands of complex industrial applications.
Read more
Quick view

GE PMC-0247RC-282000 350-93750247-282000F Compact Intelligent PLC & I/O Module for GE PACSystems RX3i

Technical Specifications:
  • Function Type: This module serves as a processor or input/output (I/O) interface component within the turbine control system, responsible for signal processing, data acquisition, and command execution.
  • Processor and Memory: Equipped with a high-speed digital signal processor (DSP) and sufficient onboard memory to support real-time control algorithms, diagnostics, and firmware operations.
  • Communication Interface: Supports high-speed communication via Ethernet or fiber optic links, enabling integration with the central control system and other field devices using protocols such as Profibus, Modbus, or proprietary GE control networks.
  • I/O Support: Designed to interface with analog and digital signals from sensors and actuators, including temperature, pressure, speed, and valve position feedback.
Read more
Quick view

GE VMIVME-2540 Intelligent Counter/Controller

Technical Specifications:

  • Module Type: 16-channel analog-to-digital input module for VMEbus systems.
  • Input Resolution: 16-bit resolution ensures high accuracy and fine signal discrimination across the measurement range.
  • Input Voltage Ranges: Supports multiple selectable input ranges including ±10 V, ±5 V, 0–10 V, and 0–5 V, accommodating a wide variety of sensor and transducer outputs.
  • Sampling Rate: Capable of high-speed data acquisition with a per-channel sampling rate up to 100 kHz, enabling real-time monitoring of fast-changing signals.
  • Analog Inputs: Features 16 single-ended or 8 differential input channels, providing flexibility in signal connection and noise rejection.
Read more
Quick view